1/2" Shock Hardware

Set Descending Direction

17 Item(s)

  1. Premium sealed shock hardware for bikes that like to get wet and muddy. 21.9 mm length to fit 1/2" shock eyelets. Heavy duty stainless steel wear surfaces, IGUS pre-tensioned bushing for maximum life and Shockcraft's own sealing collars to keep contaminants out. Learn More
  2. Flanged bushings for shock eyelets
    Installed as a pair with o-rings (not included) for new fitment or repair
    Straight replacement for similar bushings from Fox, Trelleborg etc

    Note these have a tighter ID than Fox & IGUS
    They can be reamed to size after installation if they are too tight

    Learn More
  3. Fox Flanged bushings for shock eyelets
    Installed as a pair with o-rings (not included) for repair
    Straight replacement for genuine Fox flanged bushings provided the pin isn't worn

    If you have a worn pin causing a knock, then use the green versions which have a tighter ID

    Learn More
  4. Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later)
    21.8 mm total width 8 mm bolt hole
    Two piece top-hat design
    Manitou Part Code: 142-27125-K003 Learn More
  5. Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom fitted in our workshop to your shock's individual eyelet tolerances Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and standard IGUS bushing For pin lengths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after receipt of shock Learn More
  6. Shock hardware custom fitted in our workshop to your shock's individual eyelet tolerances. Widths from ~16mm on up. Virtually any diameter and bolt hole possible. Includes stainless steel pin with plastic collars and standard IGUS bushing Allow 7 days lead time after receipt of shock Learn More
  7. Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom made to fit your shock eyelet and frame Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and pre-tensioned IGUS bushing for best fit For pin lengths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after order confirmation Learn More
  8. Heavy duty stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit Custom made to fit your shock eyelet and frame Allow 7 days lead time after order confirmation Learn More
  9. Offset Shock Hardware (Shockcraft)

    $90.00

    Custom made to order

    Heavy duty offset stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit

    Custom made to fit your shock eyelet and frame

    This is shock hardware for one end of shock only

    Allow 7 days lead time after order confirmation

    Important: Check clearance between frame mounting tabs and shock body is sufficient to run offset hardware.  Also check suspension and tyre clearance throughout the stroke


    Learn More
  10. Loose flange adapter collars (pair) with standard size IGUS bushing and o-rings for repair of worn Fox flanged bushings.

    One kit repairs one end of rear shock.

    Learn More
  11. Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later) 21.8 mm total width 6 mm bolt hole Two piece top-hat design Manitou Part Code: 142-27124-K003 Learn More
  12. Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later) 22.2 mm total width 6 mm bolt hole Two piece top-hat design Manitou Part Code: 142-27124-K005 Learn More
  13. Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later) 30 mm total width 8 mm bolt hole Two piece top-hat design Manitou Part Code: 142-27125-K024 Learn More
  14. Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later) 40 mm total width 8 mm bolt hole Three piece pin and collar design Manitou Part Code: 142-27125-K047 Learn More
  15. Straight replacement for shock eyelets in Modern Manitou, Modern RS, Fox, 5th Element, Marzocchi & Stratos Rear Shock Eyelets 1/2" ID x 1/2" Wide. 

    We can fit this into your shock and offer a full shock hardware manufacturing/fitting service.

    Learn More
  16. Harder wearing upgrade for Modern Manitou, Modern RS, Fox, 5th Element, Marzocchi & Stratos Rear Shock Eyelets 1/2" ID x 1/2" Wide.  Available with shock eyelet pressing or complete custom fitted shock hardware.

    Learn More
  17. Harder wearing upgrade for Modern Manitou, Modern RS, Fox, 5th Element, Marzocchi & Stratos Rear Shock Eyelets.
    1/2" ID x 1/2" Wide.  
    Pre-tensioned bushing to accomodate small variations in eyelet diameter and shape without binding or play Available with shock eyelet pressing or complete custom shock hardware

    Learn More

Set Descending Direction

17 Item(s)