You have no items in your shopping cart.
From: US$27.08
To: US$39.12
Final sizing and tolerancing of fork bushings to ensure minimal friction and maximum performance. Cures issue of friction and stiction to improve small bump control. Also reduces break-in time of a new fork to zero.
Burnish sizes are carefully chosen to provide maximum oil film thickness without any knocking or noticable play.
Available immediately for 30 mm, 32 mm, 34 mm, 35 mm and 36 mm forks. Other sizes will have a slight delay as we manufacture tooling.
From: US$114.34
To: US$324.96
Permanent repair of creaking and ticking noises from fork crowns. Also improves fork stiffness. Shockcraft has the technology and understanding to dismantle and reassemble fork crowns for safe and permanent creak repair.
Note that damaged crowns will be rejected. This is not a repair for parts stretched or bent.
Pricing depends on whether we receive a stripped Crown Steerer Unit (CSU) only or a whole fork. If you send a whole fork we need to strip and rebuild it.sembly.
Forks with cartridge dampers (e.g. Fox FIT/GRIP/GRIP2/CTD, RockShox Charger, Manitou MC2 or Mezzer) require a minimum of a Lower Leg & Air Spring Service.
Forks with in-leg or open bath dampers (e.g. Fox open bath, RockShox all except Charger, Marzocchi Z2) require a minimum of a Standard Service. The service labour pricing provided excludes additional repair. Parts, oil and freight are additional and vary depending on the brand & model and the problems found.
Available immediately for RS Zeb, RS Yari/Lyrik 35 mm, RS Pike 35 mm, RS 32 mm Fox 38 mm, Fox 36 mm, Fox 34 mm, Fox 32 mm Manitou 37, 34, 32 and 30 mm, MRP Ribbon 35mm forks and more. New sizes have a slight delay as we design and manufacture tooling.
From: US$90.27
To: US$532.58
Replacement of individual Stanchion or Steerer Tubes in fork crowns. Shockcraft has the technology and understanding to dismantle and reassemble fork crowns for repair.
Note that damaged crowns and tubes will be rejected.
Shockcraft Part Code: LBR-FORKTUBESWAP
In Stock
SKF Low Friction Flangeless Fork Seal kit for Fox 36 mm and Marzocchi Z1 2019+ forks
These flangeless seals have the same fork compatibility as the flanged option
Flangeless seals provide a tighter fit into the lower leg (to resist popping out with internal air leaks) which makes them more difficult to install than flanged seals
We recommend the use of a seal press tool for installation
Available Ex NZ Supplier 2 Days
Fox Service Set 2021 36 GRIP2 Cartridge - 180mm VVC HSR / LSR / HSC/ LSC (Fox)
Also fits Marzocchi Z1 2019+ forks
Complete damper assembly with adjuster knobs for repair, upgrade or tuning
Available stock or with Shockcraft tuning
Fox Part Code: 820-18-335-KIT
In Stock
Air spring volume spacer for Fox 36 forks
Note that E bike F36 forks have thicker wall stanchions and use F34 volume spacers
Orange colour
10 cc volume each
Fox Part Code: 234-04-736
Last One Left
Vorsprung Fractive upgrade tuning kit for Fox FIT4 Factory-Series fork dampers 2015-2019
Fits only FIT4 factory series dampers with LSC adjuster dial in centre of the Firm-Medium-Open dial
Requires significant tools and knowledge to install
Can be installed as part of any Shockcraft complete-fork or damper-only service (book here)
In Stock Now
Vorsprung Luftkappe air piston with higher volume negative
Fits 2018+ Fox Float 36 Evol Performance & Factory Series forks
Requires roll pin tool to install
Can be installed as part of any Shockcraft service (book here)
From: US$388.15
To: US$413.24
Vorsprung Smashpot coil conversion system for Fox 36 forks
Fits 2015+ Fox 36 forks with M33x0.8mm top-caps
2021+ Fox 36 forks require the 20 mm top cap adapter
Includes adjustable hydraulic bottom-out system
Spring rates available from 30-80 lb/in
Will not fit E bike forks with smaller ID stanchions and caps
Requires strip down, tools and oil to install
Can be installed as part of any Shockcraft service (book here)
Ordered in from NZ supplier upon customer order. Usually available approx 2 days lead-time.
From: US$388.15
To: US$397.42
Vorsprung Smashpot coil conversion system for Marzocchi Z1 forks
Fits 2019+ Marzocchi Z1 forks with M33x0.8mm top-caps
Includes adjustable hydraulic bottom-out system
Spring rates available from 30-80 lb/in
Will not fit E bike forks with smaller ID stanchions and caps
Requires strip down, tools and oil to install
Can be installed as part of any Shockcraft service (book here)
Ordered in from NZ supplier upon customer order. Usually available approx 2 days lead-time.