WE ARE OPEN
Click here for updates on our current status.
 

Upgrades

Set Descending Direction

7 Item(s)

  1. A simpler, lighter and more compact axle to replace the QR15 hexlock in Manitou Magnum, Machete, Mattoc, Minute or Marvel QR15 forks.
    Axle can be tensioned and removed with a single 6 mm hex key.
    Current model is Black.

    Manitou Part Code: 141-33147-K001

    Learn More
  2. Mattoc Pro MC2 Upgrade Kit (Manitou)

    Starting at: US$10.79

    Upgrade your Mattoc Expert to Mattoc Pro specification.
    Requires the Mattoc Pro rebound shaft assembly
    Compression damping requires either the Mattoc Pro MC2 compression assembly or convert your Expert compression damper with the Pro HBO Cup.
    27" wheel size for up to 160 mm travel

    Manitou Part Codes: 141-30996-K017 (Rebound Assembly) & 141-30996-K001 (Compression Damper Assembly) or 126-30377 (Mattoc Pro HBO Cup)

    Learn More
  3. Fork Bushing Burnishing (Shockcraft)

    From: US$27.83

    To: US$40.21

    Final sizing and tolerancing of fork bushings to ensure minimal friction and maximum performance.  Cures issue of friction and stiction to improve small bump control.  Also reduces break-in time of a new fork to zero.
    Burnish sizes are carefully chosen to provide maximum oil film thickness without any knocking or noticable play.

    Available immediately for 30 mm, 32 mm, 34 mm, 35 mm and 36 mm forks.  Other sizes will have a slight delay as we manufacture tooling.

    Learn More
  4. Kit includes 2 high quality flangeless seals, 2 foam rings and Slickoleum grease.
    Fits 34 mm stanchioned Manitou forks from 2006 to present.
    Flanged type for 44mm pocket.
    Special compound for low friction & extreme low temperature performance.

    These flangeless seals have the same fork compatibility as the flanged option
    Flangeless seals provide a tighter fit into the lower leg (to resist popping out with internal air leaks) which makes them more difficult to install than flanged seals
    We recommend the use of a seal press tool for installation to keep flangeles seals straight and set depth correctly.


    Manitou Part Code: 141-39022-K020
    Replaces Part Numbers 141-34000, 141-30996-K007 & 83-2969 Learn More
  5. IVA: Incremental Volume Adjust
    A 5 position spacer system to tune positive air chamber volume and increase progression
    M32 x 1.0 mm thread

    Manitou Part Code: 141-32668-K001

    Learn More
  6. Mattoc/Magnum IRT Upgrade Kit (Manitou)

    US$115.20

    Last One Left

    IRT: Infinite Rate Tune
    Adds a second air chamber for independent tuning of mid-end stroke.
    Coarse thread M32x1.0mm for 2014-2019 Mattoc, Magnum, Mastodon Pro and Expert level forks.
    Manitou Part Code: 141-32668-K003 Learn More
  7. Alternative product: 34 mm Fork Seal Kit Low Friction Flangeless (Manitou)

    Kit includes 2 high quality Trelleborg Flanged seals, 2 foam rings and Slickoleum grease.
    Fits 34 mm stanchioned Manitou forks from 2006 to present.
    Flanged type for 44mm pocket.
    Special compound for low friction & extreme low temperature performance

    These flanged seals have the same fork compatibility as the flangeless option.
    Flangeless seals provide a tighter fit into the lower leg (to resist popping out with internal air leaks) which makes them more difficult to install than flanged seals.
    A seal press tool is not essential for installation of the flanged seals but it does make the job easier.


    Manitou Part Code: 141-34000
    Replaces Part Numbers 141-30996-K007 & 83-2969

    Learn More
    • Out of stock

Set Descending Direction

7 Item(s)