Shaft clamp tool for use in installation of Luftkappe & Secus

Learn More

SKF seal head upgrade/replacement for RockShox charger 1 dampers
Fits Pike, Lyrik & Boxxer forks, both RC & RCT3 with Charger 1
Upgrade for early Pike forks built with Trelleborg seal head.
Replacement part for seal head on later model Pike, Lyrik & Boxxer forks

SRAM Part Code: 11.4015.353.030 Learn More

Final sizing and tolerancing of fork bushings to ensure minimal friction and maximum performance.  Cures issue of friction and stiction to improve small bump control.  Also reduces break-in time of a new fork to zero.
Burnish sizes are carefully chosen to provide maximum oil film thickness without any knocking or noticable play.

Available immediately for 30 mm, 32 mm, 34 mm, 35 mm and 36 mm forks.  Other sizes will have a slight delay as we manufacture tooling.

Learn More

Labour for replacement or resizing of fork bushings to fix looseness, knocking or play.  Includes burnishing to final size.

Available immediately for 28.6 mm, 30 mm, 32 mm, 34 mm, 35 mm, 36 mm, 37 mm, 38 mm and 40 mm forks.  Other sizes will have a slight delay as we manufacture tooling.

Note wiper seals need removed for this service and almost always require replacement.

Price excludes cost of replacement bushings.

Learn More

Shockcraft shim and drawing kit for revalving Vorsprung Smashpot HBO
Allows revalving of the HBO circuit to be softer and allow full use of the last 30 mm of travel
4 tunes shown on the drawing, Bypass, Soft, Medium and Firm plus Stock
Drawing lays out the shims required for each tune (paper drawing & to scale)
Allows full travel without hitting the wall
Installation requires special tools and knowledge
Recommend Motorex Supergliss 100K (warm climate), Supergliss 68K (cool climate) or Motorex 2 to 7.5 wt

Shockcraft can revalve the HBO during service if you don't feel confident doing it yourself Learn More

Adapter for installing 2014+ RS Pike/Lyrik Solo Air Luftkappe for A2 chassis Pike into 2018 RockShox Pike with B1 chassis.

Note 29+ Pike (2017/18) is built on the Lyrik/Yari B1 chassis and does not require this adapter.

Learn More

Vorsprung Luftkappe air piston with higher volume negative
Fits 2014-2017 RockShox Pike & Lyrik forks
Fits 2018+ Lyrik & Yari
Fits 2018+ Rockshox Pike with an A2 Adapter.
Not compatible with Debonair V2 or V3 shafts.
Requires 10 mm shaft clamp to install
Can be installed as part of any Shockcraft service (book here)

Learn More

Vorsprung Luftkappe extended air piston and low volume sealhead for RockShox Zeb forks
Fits 2021-22 RockShox Zeb forks, fits 2023 Zeb if 2021-22 air shaft installed
Requires 10 mm shaft clamp to install
Can be installed as part of any Shockcraft service (book here)

Learn More

Purchase a new Dorado Pro 37 mm 2022+ damper with Shockcraft Rockeater Tune to upgrade your Dorado Pro 37 mm fork

The Rockeater Tune is a preconfigured set of modifications and internal tuning which is targeted at 70-80 kg riders who like to ride rough stuff fast without getting beaten
They have enough range to also work great for riders from 60-90 kg
But even outside those limits they're better than anything you'll find factory

The Rockeater Tunes are based on our Matrix & Custom Tune series, incorporating Unharsh Modifications where needed.  But it's simpler.  There are no calculations or data needed.  We will service, install and dyno test to make sure it's running perfectly.

As the Rockeater Tunes are a one-size-fits-all upgrade, they provide the same performance and improvements for any future owners, preserving your investment.

Pricing & Availability
This product is a new Manitou Dorado Pro 37 mm 2022+ damper with a Rockeater Tune, which includes labour, machining, new parts, consumables and fluids

Damper Manitou Part Code: 141-38380-K021

Want your existing Dorado damper tuned?
You can also send us your existing Dorado Pro 37 mm damper or fork for tuning.  We have both Custom Tune & Rockeater Tune options. Learn More

BoXXer Charger 2.1 RC2 damper upgrade kit
Fits 35 mm BoXXer forks 2019+ C1+
Includes complete right side internals

SRAM Part Code: 00.4020.171.000

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.

Shockcraft can tune this damper for you before delivery Learn More

Purchase a new BoXXer C1+ 2019+ Charger 2.1 RC2 damper with Shockcraft Matrix Tune to upgrade your RockShox BoXXer 2019+ fork

Our Matrix Tune & Unharsh Modifications for these dampers are for your weight, bike geometry and riding style.  We remove harshness, increase support and compliance, while providing a lively playful feel.

Pricing & Availability
This product is a new RockShox BoXXer C1+ 2019+ Charger 2.1 RC2 damper with modifications & tuning, which includes labour, machining, new parts, consumables and fluids

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.
Damper SRAM Part Code: 00.4020.171.000

Rockeater Tune
We also have our Rockeater Tuned BoXXer Charger 2.1 RC2 dampers, info here.

Want your existing Charger damper tuned?
You can also send us your existing BoXXer Charger damper or fork for tuning.  We have both Matrix Tune & Rockeater Tune options. Learn More

Purchase a new BoXXer C1+ 2019+ Charger 2.1 RC2 damper with Shockcraft Rockeater Tune to upgrade your RockShox BoXXer 2019+ fork

The Rockeater Tune is a preconfigured set of modifications and internal tuning which is targeted at 70-80 kg riders who like to ride rough stuff fast without getting beaten
They have enough range to also work great for riders from 60-90 kg
But even outside those limits they're better than anything you'll find factory

The Rockeater Tunes are based on our Matrix & Custom Tune series, incorporating Unharsh Modifications where needed.  But it's simpler.  There are no calculations or data needed.  We will service, install and dyno test to make sure it's running perfectly.

As the Rockeater Tunes are a one-size-fits-all upgrade, they provide the same performance and improvements for any future owners, preserving your investment.

Pricing & Availability
This product is a new RockShox BoXXer C1+ 2019+ Charger 2.1 RC2 damper with a Rockeater Tune, which includes labour, machining, new parts, consumables and fluids

The dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.
Damper SRAM Part Code: 00.4020.171.000

Matrix Tune
If you want the full experience of a Matrix Tuned RockShox BoXXer C1+ 2019+ Charger 2.1 RC2 damper we still have these too.  Information and pricing is here.

Want your existing Charger damper tuned?
You can also send us your existing BoXXer Charger damper or fork for tuning.  We have both Matrix Tune & Rockeater Tune options. Learn More

Charger 2.1 Damper Seal-Head.
Also fits Charger 2.0 damper
Red colour and lower friction seal than previous
Use for repair or service.

SRAM Part Code: 11.4018.107.000 Learn More

These are only available for Pike, other applications have been superseded by the Debonair C1 (V3).

Superseded by SRAM-LYRIKPIKEDEBONAIR-AIRSHAFTUPV3

Debonair name was used in Solo Air Lyrik and Yari forks in 2018.  We call this Debonair V1.
Debonair V2 was introduced for MY 2019.  It features shafts with higher negative air volume and lower friction than previous Solo-Air air spring shafts.  Visible differences are the red flat seal-head, plastic moulded grey or black piston and removable shaft foot.
This bigger negative volume and lower friction gives you better small bump response and lets you run more air pressure for more mid stroke support.  They are a bolt-in upgrade, but only fit solo-air forks.  Debonair V2 shafts are also available in different lengths if you want to change your fork travel.  Select the correct one for your forks.

These are available for self-install or can be installed as part of a Shockcraft service. Learn More

RockShox DebonAir V3 Seal Head Upgrade Kit (SRAM)

Contains a new seal-head and shaft foot to upgrade Debonair V2 (MY2019 or 2020)  to Debonair V3 (MY 2021)
This kit only works on Debonair 2 shafts, identified by a moulded plastic black or grey air piston (visible down the top of the stanchion).
It is not compatible with earlier Solo Air shafts or Debonair v1 (wich had a silver bolt visible in the top of the air piston).

Fits Pike, Revelation, Lyrik and Yari with Debonair V2 air shafts.

SRAM Part Code:  00.4020.573.000 Learn More

Debonair V3 (RS calls it Debonair C1) is a new design for mid 2020 release to make bikes ride higher in the travel and use travel more easily.
It is identified by a longer red shaft foot and a red base-plate which is hollow underneath.

These are available for self-install or can be installed as part of a Shockcraft service.  Sizes are specific to each model, generation and travel of fork.

All sizes ordered in from supplier upon customer order.  Usually available approx 2 days lead-time.

V3 are no longer available for Rockshox Pike A1-A2, use RockShox DebonAir V2 Air Shaft Upgrade (SRAM)

Learn More

Self contained Lyrik/Yari Charger 2.1 RC2 damper for repair or upgrade of RockShox Lyrik B1+ & Yari A1+ 2016+ forks
Fits 35 mm Lyrik 27/29, Yari 27/29 & Pike A2 29+ forks which use the Lyrik chassis
Adjustable 4 click High Speed Compression (HSC), 19 click Low Speed Compression (LSC) and Low Speed rebound (LSR)
580 mm overall length
For up to 180 mm travel
Includes adjuster knobs & foot bolt
Top cap threads 32 x 0.5 mm
Shipping dimensions:  75 x 75 x 630 mm
Charger 2.1 is a mid 2019 update with better damping circuits, lower friction and softer compression damping than Charger 2.0

SRAM Part Code: 00.4020.170.000

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.

Shockcraft can tune this damper for you before delivery.  This improves small bump compliance and support.  Important for hard and fast riders.

Learn More

Purchase a new Lyrik B1+/Yari A1+ 2016+ Charger 2.1 RC2 damper with Shockcraft Matrix Tune to upgrade your RockShox 35 mm Lyrik 27/29, Yari 27/29 or Pike A2 29+ forks

Our Matrix Tune & Unharsh Modifications for these dampers are for your weight, bike geometry and riding style.  We remove harshness, increase support and compliance, while providing a lively playful feel.

Pricing & Availability
This product is a new RockShox Lyrik B1+/Yari A1+ 2016+ Charger 2.1 Damper RC2 with modifications & tuning, which includes labour, machining, new parts, consumables and fluids

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.
Damper SRAM Part Code: 00.4020.170.000

Rockeater Tune
We also have our Rockeater Tuned Lyrik/Yari Charger 2.1 RC2 dampers, info here.

Want your existing Charger damper tuned?
You can also send us your existing Lyrik Charger damper or fork for tuning.  We have both Matrix Tune & Rockeater Tune options. Learn More

Purchase a new Lyrik B1+/Yari A1+ 2016+ Charger 2.1 RC2 damper with Shockcraft Rockeater Tune to upgrade your RockShox 35 mm Lyrik 27/29, Yari 27/29 or Pike A2 29+ forks

The Rockeater Tune is a preconfigured set of modifications and internal tuning which is targeted at 70-80 kg riders who like to ride rough stuff fast without getting beaten
They have enough range to also work great for riders from 60-90 kg
But even outside those limits they're better than anything you'll find factory

The Rockeater Tunes are based on our Matrix & Custom Tune series, incorporating Unharsh Modifications where needed.  But it's simpler.  There are no calculations or data needed.  We will service, install and dyno test to make sure it's running perfectly.

As the Rockeater Tunes are a one-size-fits-all upgrade, they provide the same performance and improvements for any future owners, preserving your investment.

Pricing & Availability
This product is a new RockShox Lyrik B1+/Yari A1+ 2016+ Charger 2.1 RC2 damper with a Rockeater Tune, which includes labour, machining, new parts, consumables and fluids

The dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.
Damper SRAM Part Code: 00.4020.170.000

Matrix Tune
If you want the full experience of a Matrix Tuned RockShox Lyrik B1+/Yari A1+ 2016+ Charger 2.1 RC2 damper we still have these too.  Information and pricing is here.

Want your existing Charger damper tuned?
You can also send us your existing Lyrik Charger damper or fork for tuning.  We have both Matrix Tune & Rockeater Tune options.


Learn More

Self contained Pike Charger 2.1 RC2 damper for repair or upgrade of RockShox Pike forks
Fits 35 mm Pike B1+ 2018+ forks
Includes adjuster knobs & foot bolt
Charger 2.1 is a mid 2019 update with better damping circuits, lower friction and softer compression damping than Charger 2.0

SRAM Part Code: 00.4020.169.005

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.

Shockcraft can tune this damper for you before delivery.  This improves small bump compliance and support.  Important for hard and fast riders.

Learn More

Purchase a new Pike B1+ 2018+ Charger 2.1 RC2 damper with Shockcraft Matrix Tune to upgrade your RockShox 35 mm Pike forks

Our Matrix Tune & Unharsh Modifications for these dampers are for your weight, bike geometry and riding style.  We remove harshness, increase support and compliance, while providing a lively playful feel.

Pricing & Availability
This product is a new RockShox Pike B1+ 2018+ Charger 2.1 Damper RC2 with modifications & tuning, which includes labour, machining, new parts, consumables and fluids

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.
Damper SRAM Part Code: 00.4020.169.005

Rockeater Tune
We also have our Rockeater Tuned Pike Charger 2.1 RC2 dampers, info here.

Want your existing Charger damper tuned?
You can also send us your existing Lyrik Charger damper or fork for tuning.  We have both Matrix Tune & Rockeater Tune options. Learn More

Purchase a new Pike B1+ 2018+ Charger 2.1 RC2 damper with Shockcraft Rockeater Tune to upgrade your RockShox 35 mm Pike fork

The Rockeater Tune is a preconfigured set of modifications and internal tuning which is targeted at 70-80 kg riders who like to ride rough stuff fast without getting beaten
They have enough range to also work great for riders from 60-90 kg
But even outside those limits they're better than anything you'll find factory

The Rockeater Tunes are based on our Matrix & Custom Tune series, incorporating Unharsh Modifications where needed.  But it's simpler.  There are no calculations or data needed.  We will service, install and dyno test to make sure it's running perfectly.

As the Rockeater Tunes are a one-size-fits-all upgrade, they provide the same performance and improvements for any future owners, preserving your investment.

Pricing & Availability
This product is a new RockShox Pike B1+ 2018+ Charger 2.1 RC2 damper with a Rockeater Tune, which includes labour, machining, new parts, consumables and fluids

The dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.
Damper SRAM Part Code: 00.4020.169.005

Matrix Tune
If you want the full experience of a Matrix Tuned RockShox Pike B1+ 2018+ Charger 2.1 RC2 damper we still have these too.  Information and pricing is here.

Want your existing Charger damper tuned?
You can also send us your existing Lyrik Charger damper or fork for tuning.  We have both Matrix Tune & Rockeater Tune options. Learn More

Charger 2 Damper Upgrade Kit
Fits 32mm SID 27-29" 2012-2016, Reba 27-29 (2012-2017) and Bluto
Max 120mm travel
RLC (rebound, lockout and compression) adjust.
With One-Lock cable remote.

SRAM Part Code: 00.4018.783.011 Learn More

Service, tuning and upgrade pricing for RockShox Zeb 2021+
Includes labour, consumables and fluids
Excludes wiper seals, repairs & repair parts

Select special service, upgrade & tuning options to view pricing
See Related Products for more info on each selectable item Learn More

Damper Upgrade Kit CHARGER2.1 RC2 for Zeb A1+ 2021 (SRAM)
Self contained charger2.1 damper for repair or upgrade from sub-par Charger R/RC versions.
Adjustable 4 click High Speed Compression (HSC), 19 click Low Speed Compression (LSC) and Low Speed rebound (LSR)
2021 Zeb A1 only.  Max 200mm travel.
Includes adjuster knobs & foot bolt.

SRAM Part Code: 00.4318.048.000

Shockcraft can tune this damper for you before delivery.  This improves compliance, support and stability.  Details here for purchase of this damper tuned & modified.

Learn More