Shaft clamp tool for use in installation of Luftkappe & Secus

Learn More

Vorsprung Fractive upgrade tuning kit for Fox FIT4 Factory-Series fork dampers 2015-2019
Fits only FIT4 factory series dampers with LSC adjuster dial in centre of the Firm-Medium-Open dial
Requires significant tools and knowledge to install
Can be installed as part of any Shockcraft complete-fork or damper-only service (book here)

Learn More

Shockcraft shim and drawing kit for revalving Vorsprung Smashpot HBO
Allows revalving of the HBO circuit to be softer and allow full use of the last 30 mm of travel
4 tunes shown on the drawing, Bypass, Soft, Medium and Firm plus Stock
Drawing lays out the shims required for each tune (paper drawing & to scale)
Allows full travel without hitting the wall
Installation requires special tools and knowledge
Recommend Motorex Supergliss 100K (warm climate), Supergliss 68K (cool climate) or Motorex 2 to 7.5 wt

Shockcraft can revalve the HBO during service if you don't feel confident doing it yourself Learn More

Adapter for installing 2014+ RS Pike/Lyrik Solo Air Luftkappe for A2 chassis Pike into 2018 RockShox Pike with B1 chassis.

Note 29+ Pike (2017/18) is built on the Lyrik/Yari B1 chassis and does not require this adapter.

Learn More

Vorsprung Luftkappe air piston with higher volume negative
Fits 2018+ Fox Float 34 Evol Performance & Factory Series forks
Fits 2021+ Fox 38 forks
Requires roll pin tool to install as it is pinned to the air shaft.
Can be installed as part of any Shockcraft service (book here)

Learn More

Vorsprung Luftkappe air piston and low volume sealhead for Fox 34 NA2 forks
Fits 2016-17 Fox Float 34 NA2 Performance & Factory Series forks (130+ mm only)
Requires shaft clamp to install and is threaded onto air shaft.
Included low volume sealhead increases negative volume similar to 2018 Evol spec
Can be installed as part of any Shockcraft service (book here)

Learn More

Vorsprung Luftkappe air piston with higher volume negative
Fits 2018+ Fox Float 36 Evol Performance & Factory Series forks
Requires roll pin tool to install
Can be installed as part of any Shockcraft service (book here)

Learn More

Vorsprung Luftkappe air piston with higher volume negative
Fits 2014-2017 RockShox Pike & Lyrik forks
Fits 2018+ Lyrik & Yari
Fits 2018+ Rockshox Pike with an A2 Adapter.
Not compatible with Debonair V2 or V3 shafts.
Requires 10 mm shaft clamp to install
Can be installed as part of any Shockcraft service (book here)

Learn More

Vorsprung Luftkappe extended air piston and low volume sealhead for RockShox Zeb forks
Fits 2021-22 RockShox Zeb forks, fits 2023 Zeb if 2021-22 air shaft installed
Requires 10 mm shaft clamp to install
Can be installed as part of any Shockcraft service (book here)

Learn More

Roll pin tool for use in installation of Luftkappe in Fox Float 34 Evol 2018+, 34 NA2 2016-17 & 36 Evol 2018+ forks

Learn More

Air piston removal tool for Fox 40 mm forks
For use in installation of Vorsprung Secus Learn More

If you have a Debonair C1 air spring for RockShox Lyrik/Pike, a replacement 35 mm Debonair this B1-style sealhead is now available.
The C1 sealhead effectively shortens the air shaft and reduces/eliminates the pneumatic topout control present in the B1/B2 air shaft assemblies.
While the Secus can be physically attached to a C1 Debonair air shaft assembly, it will reduce your travel and may top out noticeably loudly.  We strongly recommend replacing the C1 sealhead with a B1 sealhead. Learn More

Spare foot nut for Vorsprung Secus. Learn More

Secus Fox A1 foot stud to fit a Secus to Fox 32, 34 & 36 mm stanchioned forks Learn More

Secus Fox A2 foot stud to fit a Secus to Fox 38 mm stanchioned forks Learn More

Secus Fox A3 foot stud to fit a Secus to Fox 40 mm stanchioned forks
This kit includes the same foot stud as the one in the Fox A1 kit, but includes a replacement air piston for the Fox 40 Learn More

Secus RockShox A3 foot stud to fit a Secus to Rockshox forks

This supersedes the RockShox A2 foot stud.  The RockShox A3 foot stud fits all the same forks as the A1 & A2 kits, plus more.
The A1, A2 & A3 kits all share the same footstud part, but the A2 kit also includes spacer shims to allow for fitment on forks that the A1 kit did not fit. The A3 kit includes the spacer shims plus an adaptor for Buttercup air shafts.  Note that the Buttercups will be replaced.

The A3 kit includes the spacer shims plus 4x o-rings. Learn More

For the first time, Vorsprung has created an air spring with a truly better spring rate, everywhere in the travel, than a coil.  The Secus upgrade delivers the first and only single crown air spring system to really come indistinguishably close to the linear spring rate of a coil fork for the entire first 2/3rds of its travel, with the advantage of a gentle end stroke progression to prevent bottoming without the “wall of force” harshness that excessively progressive springs create.

This version of the Secus fits Fox 32, 34 & 36 mm stanchioned forks & Marzocchi Z1 2019+ forks (see Compatibility info).  Also available for RockShox & Fox 38/40 mm forks.
Learn More

For the first time, Vorsprung has created an air spring with a truly better spring rate, everywhere in the travel, than a coil.  The Secus upgrade delivers the first and only single crown air spring system to really come indistinguishably close to the linear spring rate of a coil fork for the entire first 2/3rds of its travel, with the advantage of a gentle end stroke progression to prevent bottoming without the “wall of force” harshness that excessively progressive springs create.

This version of the Secus fits Fox 38 mm stanchioned forks (see Compatibility info).  Also available for RockShox, Fox 32/34/36/40 mm & Marzocchi forks.
Learn More

For the first time, Vorsprung has created an air spring with a truly better spring rate, everywhere in the travel, than a coil.  The Secus upgrade delivers the first and only single crown air spring system to really come indistinguishably close to the linear spring rate of a coil fork for the entire first 2/3rds of its travel, with the advantage of a gentle end stroke progression to prevent bottoming without the “wall of force” harshness that excessively progressive springs create.

This version of the Secus fits Fox 40 mm stanchioned forks (see Compatibility info).  Also available for RockShox, Fox 32/34/36/38 mm & Marzocchi forks.
Learn More

For the first time, Vorsprung has created an air spring with a truly better spring rate, everywhere in the travel, than a coil.  The Secus upgrade delivers the first and only single crown air spring system to really come indistinguishably close to the linear spring rate of a coil fork for the entire first 2/3rds of its travel, with the advantage of a gentle end stroke progression to prevent bottoming without the “wall of force” harshness that excessively progressive springs create.

This version of the Secus fits RockShox forks (see Compatibility info).  Also available for Fox & Marzocchi forks.
Learn More

Available for use with a Vorsprung Secus RockShox A2 kit on newer RockShox forks with Buttercups. Learn More

20 mm top cap adapter required to fit Smashpot Coil Conversion to 2021+ Fox 36 forks Learn More

Spare heat shrink for Vorsprung Smashpot cartridge tube
Required if swapping a Smashpot when adjusting travel and/or swapping to a different fork Learn More

Vorsprung Smashpot coil conversion system for DVO Onyx SC 2019+ forks
Includes adjustable hydraulic bottom-out system
Spring rates available from 30-80 lb/in
Requires strip down, tools and oil to install
Can be installed as part of any Shockcraft service (book here)

Ordered in from NZ supplier upon customer order.  Usually available approx 2 days lead-time.

Learn More