Stanchion End Cap 068161
For 30 mm Black, R7, M30 etc
Black plastic  29.7 mm OD, 20 mm tall
1.125" 18 TPI upper thread
22 mm lower external hex
Manitou Part Code: 068161

Learn More

Travel spacer for Manitou forks
C-clip design
10 mm total height, 27.9 mm diameter, with internal recess 1 mm each side
Fits 10 mm shafts
Manitou Part Code: 121-29113

Learn More

Travel spacer for Manitou forks
C-clip design
10 mm height change, 13.8 mm total height, 31.7 mm diameter, with internal recess and external snout
Fits 12.7 mm shafts
Manitou Part Code: 121-30396

Learn More

Travel spacer for Manitou forks
C-clip design
10 mm height change, 13.8 mm total height, 31.7 mm diameter, with internal recess and external snout
Fits 10 mm damper shafts
Manitou Part Code: 121-32318

note photo is of 12.7mm shaft version: 121-30396

Learn More

Fits Manitou Black, R7, M30 & Markhor air forks with 30 mm stanchions
Thread M26.5 x 1.0 mm
Manitou Part Code: 83-2654
Supersedes 85-5803

Learn More

Air piston for Manitou 30mm forks. 
Including R7, M30 & Markhor
New design from 2020 using a quad-ring seal.

Manitou Part Code 141-33383-K001 Learn More

Air top cap to fit Manitou 32 mm forks 2008 onwards
New-Old-Stock
Fits & works with ACT coil & air spring system, ISO air, TS air, MARS air etc.
M30 x 1.0 mm thread
Includes schrader valve & cap
Supercedeed with direct fit Manitou part codes 141-27988-K013 & 141-23992-K002

Manitou Part Code:  83-3150

Learn More

Air top cap to fit Manitou Nixon 2005, Minute 2006 & Sherman 2005 forks
New-Old-Stock
1.125 x 18 TPI inperial threads
Includes schrader valve & cap

Manitou Part Code:  83-2449

Learn More

Valve-cap for Manitou 34 mm forks (Mattoc, Magnum & Mastodon) using IRT, TS or ISO air spring systems
Replacement part or upgrade for early forks using a conventional valve cap
Manitou Part Code: 127-31811

Learn More

Replacement air cap for Manitou Magnum Mattoc & Mastodon Comp forks
Can be used for pressure sensing in all Mattoc/Magnum/Mastodon forks with Dorado Air system (pump connection at bottom of forks)
Can be used to repair damaged cap on Mattoc/Magnum/Mastodon IRT system
Manitou Part Code: 141-32156-K003

Learn More

Replacement air piston for Manitou Black/Skareb forks One piece, over-moulded part Approximately 24.8 mm OD New Old Stock (NOS) Manitou Part Code: 85-5266 Learn More

IVA: Incremental Volume Adjust A 5 position spacer system to tune positive air chamber volume and increase progression
Thread M31 x 0.8 mm
Finer thread than the Mattoc/Magnum IVA upgrade kit

Manitou Part Code: 141-35384-K006 Learn More

Air spring compression rod & end cap assembly for Dorado forks 2009 onwards Fits 26" and 27" wheel sizes Manitou Part Number: 141-25983 Learn More

Compression rod for Dorado DH 2004-05

Manitou Part Code: 83-2165 Learn More

Dorado IRT (Infinite Rate Tune) upgrade assembly Fits all Manitou Dorado forks 2009 onwards Easy installation in place of lower leg air cap Includes instructions & pressure guide Manitou Part Code: 141-32668-K005 Learn More

Compression rod for Dorado MRD 2004-05

Manitou Part Code: 85-5943 Learn More

Trailside Relief press-button bleeder caps Fit all Dorado forks 2009 onwards Manitou Part Code: 141-32668-K006 Learn More

Centre air cap for Dorado forks 2009 and onwards Manitou Part Code: 141-25993 Learn More

Compression Rod for Machete Pro 27.5
Configurable for 80, 100 or 120 mm versions (Manitou)
To be used with ISO air piston (with rubber insert).
Includes stanchion end-cap, top out bumper, bottom-out bumper, negative spring and foot bolt

Manitou Part Number 141-30418-K023

Learn More

Compression Rod for Machete Pro 90
120 mm version (Manitou)
To be used with ISO air piston (with rubber insert).
Includes stanchion end-cap, top out bumper, bottom-out bumper, negative spring and foot bolt

Manitou Part Number 141-9088-K004 Learn More

Machete & Marvel ISO air piston
28.2 mm OD, 18 mm tall
M6 threaded puller hole on top
Orange anodised
Use with ISO compression rod (domed top) only
Manitou Part Code: 141-28131-K015
Replacement seal: 141-28131-K022

Learn More

Machete J-Unit air spring assembly (Manitou)
Dorado Expert spring type (positive and negative air)
Shaft assembly including volume spacers, travel spacers and stanchion cap.
M30x1.0 shaft threads, 28mm piston. M12x1.5 foot threads.
Fits 100-145mm travel.

Manitou part code:  141-36683-K006

Learn More

Compression Rod for Machete Comp 27
Configurable for 80-140mm versions (Manitou)
To be used with TS air piston (with recess).
Includes stanchion end-cap, top out bumper, bottom-out bumper, negative spring and foot bolt

Manitou Part Number 141-30418-K022

Learn More

Compression Rod for Machete Comp 29
Configurable for 80-140mm versions (Manitou)
To be used with TS air piston (with recess).
Includes stanchion end-cap, top out bumper, bottom-out bumper, negative spring and foot bolt

Manitou Part Number 141-30418-K027

Learn More

Additional 10mm travel spacers can be installed under Mastodon bottom-out bumpers to increase tyre (tire) clearance and reduce travel.

121-29113 spacer is smaller diameter used for top-out on Pro and Comp forks.  Bottomout on air side of Pro forks.
121-30396 spacer is used for bottom-out on Comp fork damper side.
121-32318 spacer is used for bottom-out on Pro fork damper side and Comp fork air side.

Learn More