You have no items in your shopping cart.
Mounting Hardware
Shock hardware to fit Manitou rear shocks. Manitou shocks earlier than ~2011 use 12 mm shock hardware, modern (2011 onwards) Manitou shocks use 1/2" shock hardware.
Below listings Include Fox and RockShox 1/2" hardware, which is compatible with modern Manitou rear shocks.
Below listings Include Fox and RockShox 1/2" hardware, which is compatible with modern Manitou rear shocks.
-
-
LRS 2005/07 Heim Joint Kit (Manitou)
US$55.21In Stock
Replacement spherical bearings for Merida/Epic rear shocks OD 16 mm, ID 8 mm New Old Stock (NOS) Manitou Part Code: 83-2272 Learn More -
OEM shock hardware for Specialized Stumpjumper/Safire/Epic frames that use AFR shocks with 12 mm eyelet Upgraded for lower friction & longer life with an IGUS pre-tensioned bushing Available in three lengths Learn More
-
Shock pin and collars to fit 12 mm ID rear shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)
38 mm total width
6 mm bolt hole
Two piece top-hat design
Photo indicative only
Manitou Part Code: 85-6205 Learn More -
Offset Shock Hardware - One End (Shockcraft)
US$88.48Custom made to order
Heavy duty offset stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit
Learn More
Custom made to fit your shock eyelet and frame
This is shock hardware for one end of shock only
Allow 7 days lead time after order confirmation
Important: Check clearance between frame mounting tabs and shock body is sufficient to run offset hardware. Also check suspension and tyre clearance throughout the stroke -
2 piece shock reducers to fit 12 mm ID shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)
Learn More
Modern shocks usually use 12.7 mm (1/2") ID eyelets; our fitted & self-install 3 piece hardware is suitable for these shocks -
Shock pin and collars to fit 12 mm ID shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)
Learn More
Modern shocks usually use 12.7 mm (1/2") ID eyelets; our fitted & self-install hardware is suitable for these shocks -
Fitted Sealed Straight Axle Shock Hardware - One End (Shockcraft)
US$70.78Custom made to order
Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom fitted in our workshop to your shock's individual eyelet tolerances Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and standard IGUS bushing For pin widths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after receipt of shock Learn More -
Fitted Straight Axle Shock Hardware - One End (Shockcraft)
US$70.78Custom made to order
Shock hardware custom fitted in our workshop to your shock's individual eyelet tolerances. Widths from ~16mm on up. Virtually any diameter and bolt hole possible. Includes stainless steel pin with plastic collars and standard IGUS bushing Allow 7 days lead time after receipt of shock Learn More -
Self-Install Sealed Straight Axle Shock Hardware - One End (Shockcraft)
US$82.58Custom made to order
Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom made to fit your shock eyelet and frame Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and pre-tensioned IGUS bushing for best fit For pin widths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after order confirmation Learn More -
Self-Install Straight Axle Shock Hardware - One End (Shockcraft)
US$70.78Custom made to order
Heavy duty stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit Custom made to fit your shock eyelet and frame Allow 7 days lead time after order confirmation Learn More -
Mounting Hardware Kit - 12.7 x 8 x 25 mm, 7 Piece (Fox)
US$31.77In Stock
Shock Hardware Kit - 8 x 25 mm, 7 piece (FOX)
8 mm bolt hole, 25mm total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars, two crush washers and o-rings.
Fits almost all Fox rear shocks.
Fox Part Code; 803-03-328 Learn More -
Mounting Hardware Kit - 12.7 x 6 x 22.2 mm, 7 Piece (Fox)
US$29.49In Stock
Shock Hardware Kit - 6 x 22.2 mm, 7 piece (FOX)
6 mm bolt hole, 0.874 inch (22.2mm) total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings.
Fits almost all Fox rear shocks.
Ref 214-08-007 FTW 1020988
Fox Part Code; 803-03-259 Learn More -
Mounting Hardware Kit - 12.7 x 6 x 21.8 mm, 7 Piece (X-Fusion)
US$23.59In Stock Now
Shock mounting hardware by X-Fusion
Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
Pin with 6 mm bolt hole, 21.8 mm width & 1/2" (12.7 mm) diameter
Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks
X-Fusion Part Code: 42-XRKBU06218-101 Learn More -
Mounting Hardware Kit - 12.7 x 6 x 22.2 mm, 7 Piece (X-Fusion)
US$23.59In Stock Now
Shock mounting hardware by X-Fusion
Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
Pin with 6 mm bolt hole, 22.2 mm width & 1/2" (12.7 mm) diameter
Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks
X-Fusion Part Code: 42-XRKBU06222-101 Learn More -
Mounting Hardware Kit - 12.7 x 8 x 21.8 mm, 7 Piece (X-Fusion)
US$23.59In Stock Now
Shock mounting hardware by X-Fusion
Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
Pin with 8 mm bolt hole, 21.8 mm width & 1/2" (12.7 mm) diameter
Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks
X-Fusion Part Code: 42-XRKBU08218-101 Learn More -
Mounting Hardware Kit - 12.7 x 8 x 22.2 mm, 7 Piece (X-Fusion)
US$23.59In Stock Now
Shock mounting hardware by X-Fusion
Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
Pin with 8 mm bolt hole, 22.2 mm width & 1/2" (12.7 mm) diameter
Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks
X-Fusion Part Code: 42-XRKBU08222-101 Learn More -
Mounting Hardware Kit - 12.7 x 8 x 30 mm, 7 Piece (X-Fusion)
US$23.59In Stock Now
Shock mounting hardware by X-Fusion
Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
Pin with 8 mm bolt hole, 30 mm width & 1/2" (12.7 mm) diameter
Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks
X-Fusion Part Code: 42-XRKBU08300-101 Learn More -
Mounting Hardware Kit - 12.7 x 8 x 20 mm, 7 Piece (X-Fusion)
US$23.59In Stock Now
Shock mounting hardware by X-Fusion
Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
Pin with 8 mm bolt hole, 20 mm width & 1/2" (12.7 mm) diameter
Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks
X-Fusion Part Code: 42-XRKBU08200-101 Learn More -
Mounting Hardware Kit - 12.7 x 8 x 21.85 mm, 5 Piece (Fox)
US$31.77Last One Left
Shock Hardware Kit - 8 x 21.85 mm, 5 piece (FOX)
8 mm bolt hole, 0.86 inch (21.85mm) total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings.
Fits almost all Fox rear shocks.
Ref 214-09-066 FTW 747764
Fox Part Code; 803-03-279
Old Fox Part Code; 803-03-165 Learn More -
Mounting Hardware Kit - 12.7 x 8 x 19 mm, 5 Piece (Fox)
US$31.77Last One Left
Shock Hardware Kit - 8 x 19 mm, 5 piece (FOX)
8 mm bolt hole, 0.75 inch (0.19mm) total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings.
Fits almost all Fox rear shocks.
Ref 214-09-004 FTW 824507
Fox Part Code; 803-03-277 Learn More -
Mounting Hardware Kit - 12.7 x 10 x 22.2 mm, 9 Piece (Fox)
US$40.05Available on backorder
Shock Hardware Kit - 10 x 22.2 mm (FOX)
10 mm bolt hole, 0.874 inch (22.2mm) total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars, two crush washers and o-rings.
Fits almost all Fox rear shocks.
Ref 214-11-001 FTW 779690
Fox Part Code; 803-03-317
Learn More -
Mounting Hardware Kit - 12.7 x 8 x 21.8 mm, 2 Piece (Manitou)
US$27.13In Stock
Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later)
21.8 mm total width 8 mm bolt hole
Two piece top-hat design
Manitou Part Code: 142-27125-K003 Learn More -
Three piece shock hardware.
12.7mm (1/2") pin
6mm bolt hole
16mm total width
Black anodised aluminium.
Works with DU or IGUS bushings.
SRAM Part Code: 11.4115.012.320 Learn More -
Three piece shock hardware.
12.7mm (1/2") pin
8mm bolt hole
54mm total width
Black anodised aluminium.
Works with DU bushings.
SRAM Part Code: 11.4115.012.290 Learn More
Mounting Hardware
Shop By
Shopping Options
- Rear Shock Model
- Frame Brand
- Bolt Hole Diameter
- Length of Mounting Hardware
- Eyelet Internal Diameter
- Bushing Type
- Bushing Internal Diameter (ID)
- Bushing Outside Diameter (OD)
- Bushing Length
Recent Posts
-
Good suspension should be stable and supportive while being planted, y... -
Deans Bank 6 Hour, Wanaka Bike Wanaka is back with their Deans Bank r... -
Bike of the Month, October 2023 Transition Smuggler with Ready Mix Tu...
Categories
Instagram
