8 mm Crush Washer
11mm OD, 1.6mm thick.
Fits Fox, Rockshox & other forks.

Sold indvidually. Learn More

Clamp block for servicing RockShox Charger 1-2.1 fork dampers
Designed and manufactured by Shockcraft
CNC machined from aluminium for a solid clamp with no scratching
6 clamp sizes - 9 to 22.2 mm

Shockcraft Part Code:  SC-CLAMP-RS-CHARGER-1-2.1-V1 Learn More

Spare pair of 8 mm crush washers for RockShox & Fox forks Protect lower legs from foot nuts/bolts These are sacrificial and should be replaced whenever fork foot nuts/bolts are removed Learn More

Spare Pair of crush washer retainers for RockShox forks. Fits with 8mm crush washers Learn More

8mm Crush Washer with 16mm flange
16mm OD, 2mm total thickness  with 1mm flange
Required on Rockshox Boxxer forks with oversize hole in the casting
Also used in Lyrik forks. Learn More

Final sizing and tolerancing of fork bushings to ensure minimal friction and maximum performance.  Cures issue of friction and stiction to improve small bump control.  Also reduces break-in time of a new fork to zero.
Burnish sizes are carefully chosen to provide maximum oil film thickness without any knocking or noticable play.

Available immediately for 30 mm, 32 mm, 34 mm, 35 mm and 36 mm forks.  Other sizes will have a slight delay as we manufacture tooling.

Learn More

Labour for replacement or resizing of fork bushings to fix looseness, knocking or play.  Includes burnishing to final size.

Available immediately for 28.6 mm, 30 mm, 32 mm, 34 mm, 35 mm, 36 mm, 37 mm, 38 mm and 40 mm forks.  Other sizes will have a slight delay as we manufacture tooling.

Note wiper seals need removed for this service and almost always require replacement.

Price excludes cost of replacement bushings.
Price shown is for labour when lower legs are removed from fork and provided dry
If whole fork is provided then minimum additional labour will be Lower Leg Service labour, as per pricing here

Learn More

Motorex 2.5 wt fork oil - 15 cSt @ 40°C

Available in 250 ml or 1 L bottles
Refill Bottles - also available in refill bottles here

Learn More

Motorex 4 wt fork oil
16 cSt @ 40°C

Fox Racing Shox use Motorex 4wt oil in its MY21 DHX2 and FLOAT X2 shocks

Available in 250 ml or 1 L bottles
Refill Bottles - also available in refill bottles here

Learn More

Try our simple fork oil selection charts to find out which oil you need for your brand of fork, terrain, climate and riding. Learn More

Fork service kit containing fork seal kit (select either SKF or SRAM), internal seal kit, fork oil, bushing lubricant, Slickoleum assembly grease, oil syringe & optional seal press tool Learn More

Permanent repair of creaking and ticking noises from fork crowns.  Also improves fork stiffness.  Shockcraft has the technology and understanding to dismantle and reassemble fork crowns for safe and permanent creak repair.

Note that damaged crowns will be rejected.  This is not a repair for parts stretched or bent.

Pricing depends on whether we receive a stripped Crown Steerer Unit (CSU) only or a whole fork.  If you send a whole fork we need to strip and rebuild it.sembly. 
Forks with cartridge dampers (e.g. Fox FIT/GRIP/GRIP2/CTD, RockShox Charger, Manitou MC2 or Mezzer) require a minimum of a Lower Leg & Air Spring Service. 
Forks with in-leg or open bath dampers (e.g. Fox open bath, RockShox all except Charger, Marzocchi Z2) require a minimum of a Standard Service.  The service labour pricing provided excludes additional repair.  Parts, oil and freight are additional and vary depending on the brand & model and the problems found.

Available immediately for RS Zeb, RS Yari/Lyrik 35 mm, RS Pike 35 mm, RS 32 mm Fox 38 mm, Fox 36 mm, Fox 34 mm, Fox 32 mm Manitou 37, 34, 32 and 30 mm, MRP Ribbon 35mm  forks and more.  New sizes have a slight delay as we design and manufacture tooling.

Learn More

Replacement of individual Stanchion or Steerer Tubes in fork crowns.  Shockcraft has the technology and understanding to dismantle and reassemble fork crowns for repair.
Note that damaged crowns and tubes will be rejected. 

Shockcraft Part Code:  LBR-FORKTUBESWAP

Learn More

Motorex Fully Synthetic lubricating oil for air pistons and suspension forks lower leg bushings.
Manitou use this exact oil as Semi-Bath fork lubrication.

Specifications:
5W40 grade
88 cSt @ 40C
Pour Point <-50C

This is a slightly less awesome lubricant than Motorex Supergliss but works over a wider temperature range and is better in the cold.

Learn More

Vorsprung Luftkappe air piston with higher volume negative
Fits 2014-2017 RockShox Pike & Lyrik forks
Fits 2018+ Lyrik & Yari
Fits 2018+ Rockshox Pike with an A2 Adapter.
Not compatible with Debonair V2 or V3 shafts.
Requires 10 mm shaft clamp to install
Can be installed as part of any Shockcraft service (book here)

Learn More

Individual volume spacer for Rockshox 35mm forks (Pike, Lyrik, Yari etc) with solo air spring (no travel adjust).
SRAM Part Code (for pack of 10): 11.4018.032.001

Learn More

SKF Low Friction Flangeless Fork Seal kit for RockShox 35 mm forks Learn More

Single foam ring for RockShox 35 mm stanchioned forks Learn More

Original RockShox 35 mm fork seal kit. Fits RockShox Boxxer (2010+), Domain Dual Crown, Lyrik & Pike (2014+) forks Learn More

These are only available for Pike, other applications have been superseded by the Debonair C1 (V3).

Superseded by SRAM-LYRIKPIKEDEBONAIR-AIRSHAFTUPV3

Debonair name was used in Solo Air Lyrik and Yari forks in 2018.  We call this Debonair V1.
Debonair V2 was introduced for MY 2019.  It features shafts with higher negative air volume and lower friction than previous Solo-Air air spring shafts.  Visible differences are the red flat seal-head, plastic moulded grey or black piston and removable shaft foot.
This bigger negative volume and lower friction gives you better small bump response and lets you run more air pressure for more mid stroke support.  They are a bolt-in upgrade, but only fit solo-air forks.  Debonair V2 shafts are also available in different lengths if you want to change your fork travel.  Select the correct one for your forks.

These are available for self-install or can be installed as part of a Shockcraft service. Learn More

RockShox DebonAir V3 Seal Head Upgrade Kit (SRAM)

Contains a new seal-head and shaft foot to upgrade Debonair V2 (MY2019 or 2020)  to Debonair V3 (MY 2021)
This kit only works on Debonair 2 shafts, identified by a moulded plastic black or grey air piston (visible down the top of the stanchion).
It is not compatible with earlier Solo Air shafts or Debonair v1 (wich had a silver bolt visible in the top of the air piston).

Fits Pike, Revelation, Lyrik and Yari with Debonair V2 air shafts.

SRAM Part Code:  00.4020.573.000 Learn More

Debonair V3 (RS calls it Debonair C1) is a new design for mid 2020 release to make bikes ride higher in the travel and use travel more easily.
It is identified by a longer red shaft foot and a red base-plate which is hollow underneath.

These are available for self-install or can be installed as part of a Shockcraft service.  Sizes are specific to each model, generation and travel of fork.

All sizes ordered in from supplier upon customer order.  Usually available approx 2 days lead-time.

V3 are no longer available for Rockshox Pike A1-A2, use RockShox DebonAir V2 Air Shaft Upgrade (SRAM)

Learn More

Self contained Lyrik/Yari Charger 2.1 RC2 damper for repair or upgrade of RockShox Lyrik B1+ & Yari A1+ 2016+ forks
Fits 35 mm Lyrik 27/29, Yari 27/29 & Pike A2 29+ forks which use the Lyrik chassis
Adjustable 4 click High Speed Compression (HSC), 19 click Low Speed Compression (LSC) and Low Speed rebound (LSR)
580 mm overall length
For up to 180 mm travel
Includes adjuster knobs & foot bolt
Top cap threads 32 x 0.5 mm
Shipping dimensions:  75 x 75 x 630 mm
Charger 2.1 is a mid 2019 update with better damping circuits, lower friction and softer compression damping than Charger 2.0

SRAM Part Code: 00.4020.170.000

These dampers are ordered in from the NZ Supplier as required.  Lead time is usually 2 days.

Shockcraft can tune this damper for you before delivery.  This improves small bump compliance and support.  Important for hard and fast riders.

Learn More

200H service kit for RockShox Yari  A1 with motion control & Dual Position Air
Contains wiper seals, foam rings, crush washers,
motion control rebound shaft seals, compression foot seals, piston ring and orings.
Dual Position Air spring o-rings.

SRAM Part Code:  00.4315.032.610
Superceeded by 00.4315.032.622 Learn More

Rebound adjuster knob and bolt for RockShox Yari forks

SRAM Part Code: 11.4015.404.027 Learn More