Manitou Mara GEN 1 Pro

The Mara Pro is Manitou's piggy back heavy duty air shock
Imperial, Metric Eyelet and Metric Trunnion versions available
Rebound adjust
High Speed Compression (HSC) adjust
Low Speed Compression (LSC) adjust
Selectable platform (work/party) switch
Fully tunable

Note on Shock Availability:
The Mara Pro Generation 1 shocks are on run-out pricing.  Sizes available as shown.

Shock Stroke Change
There is no charge for stroke change for stock Mara Inline stroke sizes.  e.g. if we have a 210 x 50 mm shock in stock but you need a 210 x 55 mm shock there is no charge to change the stroke.

Shock Length Modification
We also change shock length of new Mara Inlines at no additional charge.  e.g. we can change a 190 x 50 mm to 185 mm x 45 mm. Learn More

This is a lightly used, ex-demo shock in great condition.
Comes with the Shockcraft Warranty.

Manitou Mara Pro Shock Metric Eyelet 210 x 50 mm Ex-Demo
Can be increased to 55 mm stroke

The Mara Pro is Manitou's piggy back heavy duty air shock
Metric eyelet version (not trunnion mount)
Rebound adjust
High Speed Compression (HSC) adjust
Low Speed Compression (LSC) adjust
Selectable platform (work/party) switch
Fully tunable.

Manitou Part Code: 192-36851-A021 Learn More

This is a lightly used, ex-demo shock in great condition.
Comes with the Shockcraft Warranty.

Manitou Mara Pro Shock Metric Eyelet 190 x 45 mm Ex-Demo
Can be reduced to 40 mm stroke

The Mara Pro is Manitou's piggy back heavy duty air shock
Metric eyelet version (not trunnion mount)
Rebound adjust
High Speed Compression (HSC) adjust
Low Speed Compression (LSC) adjust
Selectable platform (work/party) switch
Fully tunable.

Manitou Part Code: 192-36851-A020 Learn More

Service for Manitou Mara Pro rear shocks

Excludes repairs & any additional repair parts
Excludes springs and pivot hardware

Learn More

Special size Manitou Mara Pro Air shock with custom shock pin to fit a Trek Slash or Remedy with Thru-Shaft Reaktiv
Thru Shaft Reaktiv shocks are 230 x 57.5 mm air spring with lower hardware offset to one side
Product includes Shockcraft Deaktiv conversion lower pin and Manitou Mara Pro piggy back shock.
Choose travel from 230 x 60 mm (stock Mara), 230 x 57.5 mm (stock trek ) to 230x65mm if you have clearance to do so.

Resulting combination bolts straight in

Learn More

Manitou Mara Pro Gen2 Air shock with conversion kit to fit a Trek Rail with Thru-Shaft Reaktiv
Thru Shaft Reaktiv shocks are 230 x 57.5 mm air spring with lower hardware offset to one side
Product includes Mara Pro Shock, Shockraft Lift Kit with conversion pin.
Optional tuning and heavy duty bolt kit.

Resulting combination bolts straight in.  The Manitou Mara Pro has adjustable HS & LS comprssion and is suited to all riding styles.  Tuning for your weight and riding style is also available - details here

Please contact us to confirm availability

Learn More

Book your demo of a new Manitou Mezzer fork and/or Manitou Mara Pro/Inline rear shock, with Hayes Dominion A4 front brake.
Simply add this product to your cart and proceed through to checkout to book your demo and confirm your address details.  We will add you to the queue for demo and advise ETA.

For our existing and trusted customers there is no fee for demo.
For new customers the demo fee is refundable upon return of the demo fork, rear shock & brakes in good condition or can be used towards purchase of a new Manitou Mara, Mezzer or Hayes Dominion brakes.

Fitment wise, the fork requires a tapered head-tube and boost front wheel.  The brake requires a 6 bolt disc hub (i.e. not Shimano centre-lock).  A 203 mm disc rotor and brake adapter are supplied.  For demo the Manitou Mara Pro is available as 210 mm i2i Length x 50 mm Stroke or 216 x mm i2i Length x 63 mm Stroke.  On purchase there is the option to add/remove spacers from the Maras to change the stroke.  For example, the 210 x 50 mm Mara Pro can be changed to a stroke of up to 55 mm.  Contact us for further details.

Manitou Mezzer pricing, details and specifications are available here.
Manitou Mara Pro pricing, details and specifications are available here.
Manitou Mara Inline pricing, details and specifications are available here.
Hayes Dominion A4 brake pricing, details and specifications are available here.

Demo is only available to New Zealand customers.
Contact us for availability in case demos are out with other customers.

Terms & Conditions apply - see below.

Learn More

Standard air can to fit metric sized Manitou Mara Pro & Mara Inline rear shocks
Smaller volume air can same as that which comes standard on the Mara Inline
Select your shock size for the appropriate air can Learn More

King air can to fit metric sized Manitou Mara Pro & Mara Inline rear shocks
Large volume air can same as that which comes standard on the Mara Pro piggyback shocks
Select your shock size for the appropriate air can Learn More

Flanged bushings for shock eyelets
Installed as a pair with o-rings (not included) for new fitment or repair
Straight replacement for similar bushings from Fox, Trelleborg etc

Note these have a tighter ID than Fox & IGUS
They can be reamed to size after installation if they are too tight

Learn More

Straight replacement for shock eyelets in Modern Manitou, Modern RS, Fox, 5th Element, Marzocchi & Stratos Rear Shock Eyelets 1/2" ID x 1/2" Wide. 

Learn More

Harder wearing upgrade for Modern Manitou, Modern RS, Fox, 5th Element, Marzocchi & Stratos Rear Shock Eyelets.
1/2" ID x 1/2" Wide.  
Pre-tensioned bushing to accomodate small variations in eyelet diameter and shape without binding or play Available with shock eyelet pressing or complete custom shock hardware

Learn More

Harder wearing upgrade for Modern Manitou, Modern RS, Fox, 5th Element, Marzocchi & Stratos Rear Shock Eyelets 1/2" ID x 1/2" Wide.  Available with shock eyelet pressing or complete custom fitted shock hardware.

Learn More

X-Fusion Flanged bushings for shock eyelets
Straight replacement for genuine Fox flanged bushings provided the pin isn't worn
Installed as a pair with o-rings (not included) for repair

If you have a worn pin causing a knock, then use the green versions which have a tighter ID

Learn More

Original Manitou decal to fit Mara king can
Black with grey, silver & red (Manitou logo)

Decal measurement = 76 mm height x 148 mm width

Manitou Part Code: 29-37595-G003 Learn More

Original Manitou decal to fit Mara king can Black with grey, silver & red (Manitou logo)

Decal measurement = 63 mm height x 150 mm width

Manitou Part Code: 29-37595-G002 Learn More

Original Manitou decal to fit Mara king can
Black with grey, silver & red (Manitou logo)

Decal measurement = 56 mm height x 150 mm width

Manitou Part Code: 29-37595-G001 Learn More

Original Manitou decal to fit Mara standard can
Black with grey, silver & red (Manitou logo)

Decal measurement = 64 mm height x 135 mm width

Manitou Part Code: 29-37594-G003 Learn More

Original Manitou decal to fit Mara standard can
Black with grey, silver & red (Manitou logo)

Decal measurement = 57 mm height x 135 mm width

Manitou Part Code: 29-37594-G002 Learn More

Original Manitou decal to fit Mara Pro reservoir
Black with grey & silver

Decal measurement = 45 mm height x 70 mm width

Manitou Part Code: 29-37596-G002 Learn More

Original Manitou decal to fit Mara Pro reservoir
Black with grey & silver

Decal measurement = 33 mm height x 70 mm width

Manitou Part Code: 29-37596-G001 Learn More

Heavy duty stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit Custom made to fit your shock eyelet and frame Allow 7 days lead time after order confirmation Learn More

Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom made to fit your shock eyelet and frame Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and pre-tensioned IGUS bushing for best fit For pin widths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after order confirmation Learn More

Shock hardware custom fitted in our workshop to your shock's individual eyelet tolerances. Widths from ~16mm on up. Virtually any diameter and bolt hole possible. Includes stainless steel pin with plastic collars and standard IGUS bushing Allow 7 days lead time after receipt of shock Learn More

Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom fitted in our workshop to your shock's individual eyelet tolerances Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and standard IGUS bushing For pin widths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after receipt of shock Learn More