You have no items in your shopping cart.
Shock Hardware
Mountain Bike Shock eyelets come in a multitude of sizes and within each of those sizes a range of tolerances. To acheive the best performance and longest life our shock hardware is designed, toleranced and selected by our mechanical engineer to work best in your application.
The basis for our custom Straight Axle Shock Hardware is a three piece system with a pin and two collars. This setup is stiffer, stronger and longer lasting than the typical two piece. Correctly toleranced, it also runs smooth and free without play. IGUS Pre-tensioned bushings are used in our self-install hardware for maximum performance and longevity. Options for specific applications include reamed fits, threaded bores, locking screws, o-ring and quad-ring seals and spherical ball mounts.
Suspension Pivot Hardware
Shockcraft can build and supply all the components to rebuild the pivots in suspension linkages using bushings as well as bearings. We carry a large range of bearings, bushings and fasteners while manufacturing custom axles, pins and spacers. Contact us for more details.
-
Fitted Sealed Straight Axle Shock Hardware - One End (Shockcraft)
US$81.32Custom made to order
Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom fitted in our workshop to your shock's individual eyelet tolerances Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and standard IGUS bushing For pin lengths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after receipt of shock Learn More -
Mounting Hardware 8 x 54 mm (SRAM)
US$21.79Three piece shock hardware.
12.7mm (1/2") pin
8mm bolt hole
54mm total width
Black anodised aluminium.
Works with DU bushings.
SRAM Part Code: 11.4115.012.290 Learn More -
Cane Creek DB Coil Trunnion Rear Shock 205 x 62.5 mm to fit Giant Reign
From: US$853.17
To: US$890.01
Cane Creek DB Coil Rear Shock for Giant Reign
Trunnion Mount top (54 mm wide, M10 x 1.0 threaded holes)
Open lower eyelet (no bushing) to fit Giant main pivot
205 mm eye to eye length 62.5 mm stroke
9.5 mm shaft
Fits Giant Reign 2018+
Spring included - select your rate (use our spring calculator to work out spring rate)
This product is special order Learn More -
Trek Remedy & Slash Cane Creek DB Coil Conversion (Shockcraft)
From: US$920.93
To: US$1,025.54
Cane Creek DB Coil shock with custom hardware to fit a Trek Slash or Remedy with Thru-Shaft Reaktiv
Learn More
Thru Shaft Reaktiv shocks are 230 x 57.5 mm air spring with lower hardware offset to one side
Product includes Shockcraft Deaktiv conversion pins, Cane Creek DB 230 x 57.5 mm coil shock and coil spring
Resulting combination bolts straight in -
Trek Remedy & Slash Cane Creek DB Air CS Conversion (Shockcraft)
From: US$860.63
To: US$928.39
Cane Creek DB Air CS shock with custom hardware to fit a Trek Slash or Remedy with Thru-Shaft Reaktiv
Learn More
Thru Shaft Reaktiv shocks are 230 x 57.5 mm air spring with lower hardware offset to one side
Product includes Shockcraft Deaktiv conversion pins and Cane Creek DB 230 x 57.5 mm air shock
Resulting combination bolts straight in -
Fox Flanged bushings for shock eyelets
Learn More
Installed as a pair with o-rings (not included) for repair
Straight replacement for genuine Fox flanged bushings provided the pin isn't worn
If you have a worn pin causing a knock, then use the green versions which have a tighter ID -
Trek Remedy & Slash Manitou Mara Pro Air Conversion (Shockcraft)
From: US$823.36
To: US$965.67
Special size Manitou Mara Pro Air shock with custom shock pin to fit a Trek Slash or Remedy with Thru-Shaft Reaktiv
Learn More
Thru Shaft Reaktiv shocks are 230 x 57.5 mm air spring with lower hardware offset to one side
Product includes Shockcraft Deaktiv conversion lower pin and Manitou Mara Pro piggy back shock.
Choose travel from 230 x 60 mm (stock Mara), 230 x 57.5 mm (stock trek ) to 230x65mm if you have clearance to do so.
Resulting combination bolts straight in -
Trek Rail Marzocchi Bomber CR Conversion (Shockcraft)
From: US$250.73
To: US$1,287.55
Custom Hardware for fitting a Marzocchi Bomber CR Coil shock to a Trek Slash with Thru-Shaft Reaktiv
Learn More
Thru Shaft Reaktiv shocks are 230 x 57.5 mm air spring with lower hardware offset to one side
Product includes conversion pins, modified Marzocchi Bomber CR 230 x 60 mm OR 230 x 65 mm coil shock and coil spring
Resulting combination bolts straight in
Choosing the right spring: use one of our spring rate calculators over here to make sure you get the right spring for your bike geometry and weight
Please contact us to confirm availability -
Mounting Hardware Kit - 8 x 20 mm, 5 piece (FOX)
US$36.50Last One Left
Shock Hardware Kit - 8 x 20 mm, 5 piece (FOX)
8 mm bolt hole, 0.787 inch (20 mm) total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings.
Fits almost all Fox rear shocks.
Ref 214-09-043 FTW 169558
Fox Part Code; 803-03-236 Learn More -
Mounting Hardware Kit - 6 x 21.85 mm, 9 piece (FOX)
US$34.30In stock
Shock Hardware Kit - 6 x 21.85 mm, 9 piece (FOX) 6 mm bolt hole, 0.86 inch (21.84mm) total width Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings. Fits almost all Fox rear shocks. Ref 214-08-006 FTW 793134 Fox Part Code: 803-03-258 Learn More -
Mounting Hardware Kit - 8 x 22.2 mm, 7 piece (FOX)
US$36.50Available on backorder
Shock Hardware Kit - 8 x 22.2 mm, 7 piece (FOX)
8 mm bolt hole, 0.874 inch (22.2mm) total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars, two crush washers and o-rings.
Fits almost all Fox rear shocks.
Ref 214-09-007 FTW 787390
Fox Part Code; 803-03-280
Photo of prior model. Fitment identical. Learn More -
Shock Eyelet Pressing
From: US$13.55
To: US$20.33
A pressing service using our custom tools which remove and install bushings and bearings without damage to your shock. If you'd like us to replace the bushings in your rear shock eyelet, click Book Now. You can select just shock eyelet pressing or other service options. You will receive a job number and details of where to send your rear shock.
Learn More
Note there is no charge for shock eyelet pressing if completed during a Shockcraft service. -
Trek Slash 2021+ Marzocchi Bomber CR Conversion (Shockcraft)
From: US$540.77
To: US$1,330.25
Custom Hardware for fitting a Marzocchi Bomber CR Coil shock to a Trek Slash 2021+ in place of a Thru-Shaft Reaktiv shock
Learn More
2021+ Slash uses a 230 x 62.5 mm shock with 54 mm top and 40 mm lower centred hardware
Product includes conversion pins, DU Bushings, Marzocchi Bomber CR 230 x 60 mm OR 230 x 65 mm coil shock and coil spring
If using a Marzocchi Bomber CR 230 x 60 mm no additional spacers/labour required to fit but you will lose some travel
If using a Marzocchi Bomber CR 230 x 65 mm then a stroke reduction is required with shock head removal & re-gas
We can change the stroke on this shock from 0-65 mm
Resulting combination bolts straight in
Choosing the right spring: use one of our spring rate calculators over here to make sure you get the right spring for your bike geometry and weight
Please contact us to confirm availability -
Mounting Hardware Kit - 10 x 22.2 mm (FOX)
US$46.01Available on backorder
Shock Hardware Kit - 10 x 22.2 mm (FOX)
10 mm bolt hole, 0.874 inch (22.2mm) total width
Contains one pair of flanged polymer bushings, aluminim pin, two collars, two crush washers and o-rings.
Fits almost all Fox rear shocks.
Ref 214-11-001 FTW 779690
Fox Part Code; 803-03-317
Learn More -
Trek Remedy 2019-21 & Slash 2018-20 Marzocchi Bomber CR Conversion (Shockcraft)
From: US$540.77
To: US$1,228.60
Custom Hardware for fitting a Marzocchi Bomber CR Coil shock to a Trek Remedy 2019-21 & Slash 2018-20 in place of a Thru-Shaft Reaktiv shock.
Learn More
2019-2021 Remedy & 2018-2020 Slash Thru Shaft Reaktiv shocks are 230 x 57.5 mm air spring with upper 54 mm pin and lower 50 mm offset pin.
Product includes conversion pins, DU Bushings, Marzocchi Bomber CR 230 x 60 mm OR 230 x 65 mm coil shock and coil spring.
We can change the stroke on this shock from 0-65 mm.
Resulting combination bolts straight in.
Choosing the right spring: use one of our spring rate calculators over here to make sure you get the right spring for your bike geometry and weight.
Please contact us to confirm availability. -
2 Piece 12.7 x 21.8 mm M8 Shock Mounting Hardware (Manitou)
US$31.17In stock
Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later)
21.8 mm total width 8 mm bolt hole
Two piece top-hat design
Manitou Part Code: 142-27125-K003 Learn More -
Fitted Straight Axle Shock Hardware - One End (Shockcraft)
US$67.77Custom made to order
Shock hardware custom fitted in our workshop to your shock's individual eyelet tolerances. Widths from ~16mm on up. Virtually any diameter and bolt hole possible. Includes stainless steel pin with plastic collars and standard IGUS bushing Allow 7 days lead time after receipt of shock Learn More -
Self-Install Sealed Straight Axle Shock Hardware - One End (Shockcraft)
US$81.32Custom made to order
Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom made to fit your shock eyelet and frame Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and pre-tensioned IGUS bushing for best fit For pin lengths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after order confirmation Learn More -
Self-Install Straight Axle Shock Hardware - One End (Shockcraft)
US$67.77Custom made to order
Heavy duty stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit Custom made to fit your shock eyelet and frame Allow 7 days lead time after order confirmation Learn More -
1/2" Low Friction Flanged Bushing Pair
US$12.16Available on backorder
Flanged bushings for shock eyelets
Learn More
Installed as a pair with o-rings (not included) for new fitment or repair
Straight replacement for similar bushings from Fox, Trelleborg etc
Note these have a tighter ID than Fox & IGUS
They can be reamed to size after installation if they are too tight -
Faux Flange Adapters - pair with IGUS bushing (Shockcraft)
From: US$10.16
To: US$23.72
Loose flange adapter collars (pair) with standard size IGUS bushing and o-rings for repair of worn Fox flanged bushings.
Learn More
One kit repairs one end of rear shock. -
Premium sealed shock hardware for bikes that like to get wet and muddy. 21.9 mm length to fit 1/2" shock eyelets. Heavy duty stainless steel wear surfaces, IGUS pre-tensioned bushing for maximum life and Shockcraft's own sealing collars to keep contaminants out. Learn More
-
Offset Shock Hardware - One End (Shockcraft)
US$101.65Custom made to order
Heavy duty offset stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit
Learn More
Custom made to fit your shock eyelet and frame
This is shock hardware for one end of shock only
Allow 7 days lead time after order confirmation
Important: Check clearance between frame mounting tabs and shock body is sufficient to run offset hardware. Also check suspension and tyre clearance throughout the stroke -
OEM shock hardware for Specialized Stumpjumper/Safire/Epic frames that use AFR shocks with 12 mm eyelet Upgraded for lower friction & longer life with an IGUS pre-tensioned bushing Available in three lengths Learn More
-
2 piece shock reducers to fit 12 mm ID shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)
Learn More
Modern shocks usually use 12.7 mm (1/2") ID eyelets; our fitted & self-install 3 piece hardware is suitable for these shocks
Recent Posts
-
Tuning is an ambiguous word. It means different things to differ... -
A new Big Bike Film Night Feature Series starts in 4 days, screening a... -
Shockcraft & Biken are continuing to operate during the current NZ...
Categories
Newsletter
Instagram
