Rear Shock Parts

0.5 inch shaft Wiper Seal
D type single lip
NBR black rubber material

Shockcraft Part Code:  S-FWI-0.5x0.75x0.125-D-NBR Learn More

Flanged bushings for shock eyelets
Installed as a pair with o-rings (not included) for new fitment or repair
Straight replacement for similar bushings from Fox, Trelleborg etc

Note these have a tighter ID than Fox & IGUS
They can be reamed to size after installation if they are too tight

Alternative is over here

Learn More

X-Fusion Flanged bushings for shock eyelets
Straight replacement for genuine Fox flanged bushings provided the pin isn't worn
Installed as a pair with o-rings (not included) for repair

If you have a worn pin causing a knock, then use the green versions which have a tighter ID

Learn More

Straight replacement for
Manitou, X-Fusion & some RockShox
Rear Shock Eyelets
12 mm x 14 mm x 12 mm Learn More

Harder wearing upgrade for Manitou, X-Fusion & some RockShox Rear Shock Eyelets 12 mm x 14 mm x 12 mm Available with shock eyelet pressing Learn More

Straight replacement for Manitou Wide (14 mm) Rear Shock Eyelets 12 mm x 14 mm x 14 mm Learn More

Harder wearing upgrade for Manitou, X-Fusion & some RockShox Rear Shock Eyelets 12 mm x 14 mm x 12 mm Pre-tensioned bushing to accomodate small variations in eyelet diameter and shape without binding or play Available with shock eyelet pressing Learn More

2 piece shock reducers to fit 12 mm ID shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)

Modern shocks usually use 12.7 mm (1/2") ID eyelets; our fitted & self-install 3 piece hardware is suitable for these shocks 

Learn More

Premium sealed shock hardware for bikes that like to get wet and muddy. 21.9 mm width to fit 1/2" shock eyelets. Heavy duty stainless steel wear surfaces, IGUS pre-tensioned bushing for maximum life and Shockcraft's own sealing collars to keep contaminants out. Learn More

Shock pin and collars to fit 12 mm ID shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)

Modern shocks usually use 12.7 mm (1/2") ID eyelets; our fitted & self-install hardware is suitable for these shocks

Learn More

ACE underbar remote from Manitou for control of dropper post
Stackable with DEUCE remote (purchase separately) for remote lockout of forks and/or shocks
ACE can be built above or below the DEUCE or either can be used standalone
To minimise weight the levers use 3 mm housing and 0.9 mm cable
Also compatible with standard 4 mm housing and 1.2 mm cable

Manitou Part Code: 193-41336-A101 Learn More

ACE & DEUCE remotes from Manitou for control of fork, shock & dropper posts
DEUCE is the suspension lockout remote lever for fork and/or rear shock
ACE is the underbar remote for dropper posts
Levers are stackable  and can be built into the configuration that makes the most sense for the individual rider
ACE can be built above or below the DEUCE or can be used standalone
To minimise weight the levers use 3 mm housing and 0.9 mm cable
Also compatible with standard 4 mm housing and 1.2 mm cable

Manitou Part Code: 193-41336-A001 Learn More

Manitou Part Code: 83-2222

Fits Manitou Swinger and Radium.

81 mm overall length, 43 mm ID. Learn More

Manitou Part Code: 83-2699

Fits Manitou Swinger and Radium.

80 mm overall length, 40 mm ID. Learn More

Manitou Part Code: 83-3003

Fits Manitou Swinger and Radium.

91 mm overall length, 40 mm ID. Learn More

Manitou Part Code: 83-2702

Fits Manitou Swinger and Radium.

92 mm overall length, 40 mm ID. Learn More

Manitou Part Code: 83-2228

Fits Manitou Swinger and Radium.

99 mm overall length, 43 mm ID. Learn More

Manitou Part Code: 83-2229

Fits Manitou Swinger and Radium.

106 mm overall length, 42 mm ID. Learn More

Manitou Part Code: 83-2230

Fits Manitou Swinger and Radium.

110 mm overall length, 43 mm ID. Learn More

SPV Volume Adjuster Top-Cap Assembly for 2004-2006 Black fork with SPV damper.
Requires thin 16mm socket to adjust volume.
M26.5 x 1.0 mm thread.  24mm piston.  No valve cap.

Manitou Part Code 85-5871 Learn More

Fork and shock Shaft Clamp Block (Manitou)
Etched part code:  172-31242
Sizes 16.3, 14, 12.6, 12, 10 & 8mm
For Most Manitou forks and shocks

Manitou Part Code:  172-31464 Learn More

Cartridge damper bleeding tool kit (Manitou)
For bleeding cartridge fork and rear shock dampers.  Including Mezzer, Dorado, Mara Pro etc.
Can also fit other brands mineral oil brakes, dropper posts etc.
Contains bleed syringes, M5 point fitting, M5 o-ring fittings, M8 o-ring fittings, tube and a torx driver.
For use with mineral oil only (no DOT fluid).
Packaged in a clip top plastic tub.

Manitou Part Code 141-30694-K020

Learn More

DEUCE remote from Manitou for suspension lockout of fork and/or shock
Stackable with ACE remote (purchased separately) for dropper posts
DEUCE can be built above or below the ACE or either can be used standalone
To minimise weight the levers use 3 mm housing and 0.9 mm cable
Also compatible with standard 4 mm housing and 1.2 mm cable

Manitou Part Code: 193-41336-A201 Learn More

Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom fitted in our workshop to your shock's individual eyelet tolerances Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and standard IGUS bushing For pin widths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after receipt of shock Learn More

Shock hardware custom fitted in our workshop to your shock's individual eyelet tolerances. Widths from ~16mm on up. Virtually any diameter and bolt hole possible. Includes stainless steel pin with plastic collars and standard IGUS bushing Allow 7 days lead time after receipt of shock Learn More