We are OPEN
Click here for updates on our current status.
 

Mounting Hardware

Shock hardware to fit Manitou rear shocks.  Manitou shocks earlier than ~2011 use 12 mm shock hardware, modern (2011 onwards) Manitou shocks use 1/2" shock hardware.

Below listings Include Fox and RockShox 1/2" hardware, which is compatible with modern Manitou rear shocks.

Set Descending Direction

1-25 of 35

Page:
  1. 1
  2. 2
  1. Manitou Part Code: 83-2273 Learn More
  2. Replacement spherical bearings for Merida/Epic rear shocks OD 16 mm, ID 8 mm New Old Stock (NOS) Manitou Part Code: 83-2272 Learn More
  3. OEM shock hardware for Specialized Stumpjumper/Safire/Epic frames that use AFR shocks with 12 mm eyelet Upgraded for lower friction & longer life with an IGUS pre-tensioned bushing Available in three lengths Learn More
  4. Shock pin and collars to fit 12 mm ID rear shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)
    38 mm total width
    6 mm bolt hole
    Two piece top-hat design
    Photo indicative only

    Manitou Part Code: 85-6205 Learn More
  5. Offset Shock Hardware - One End (Shockcraft)

    US$91.82

    Custom made to order

    Heavy duty offset stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit

    Custom made to fit your shock eyelet and frame

    This is shock hardware for one end of shock only

    Allow 7 days lead time after order confirmation

    Important: Check clearance between frame mounting tabs and shock body is sufficient to run offset hardware.  Also check suspension and tyre clearance throughout the stroke


    Learn More
  6. 2 piece shock reducers to fit 12 mm ID shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)

    Modern shocks usually use 12.7 mm (1/2") ID eyelets; our fitted & self-install 3 piece hardware is suitable for these shocks 

    Learn More
  7. Shock pin and collars to fit 12 mm ID shock eyelets (including early Manitou, X-Fusion, RockShox & Specialized AFR rear shocks)

    Modern shocks usually use 12.7 mm (1/2") ID eyelets; our fitted & self-install hardware is suitable for these shocks

    Learn More
  8. Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom fitted in our workshop to your shock's individual eyelet tolerances Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and standard IGUS bushing For pin widths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after receipt of shock Learn More
  9. Shock hardware custom fitted in our workshop to your shock's individual eyelet tolerances. Widths from ~16mm on up. Virtually any diameter and bolt hole possible. Includes stainless steel pin with plastic collars and standard IGUS bushing Allow 7 days lead time after receipt of shock Learn More
  10. Premium sealed 1/2" shock hardware for bikes that like to get wet and muddy Custom made to fit your shock eyelet and frame Includes stainless steel pin with Shockcraft's own sealing collars to keep contaminants out, and pre-tensioned IGUS bushing for best fit For pin widths 25 mm and greater both sealing collars and spacers are used Allow 7 days lead time after order confirmation Learn More
  11. Heavy duty stainless steel shock pivot pin with two plastic collars and pre-tensioned IGUS bushing for best fit Custom made to fit your shock eyelet and frame Allow 7 days lead time after order confirmation Learn More
  12. Shock Hardware Kit - 8 x 25 mm, 7 piece (FOX)

    8 mm bolt hole, 25mm total width
    Contains one pair of flanged polymer bushings, aluminim pin, two collars, two crush washers and o-rings.
    Fits almost all Fox rear shocks.

    Fox Part Code;  803-03-328 Learn More
  13. Shock Hardware Kit - 6 x 22.2 mm, 7 piece (FOX)

    6 mm bolt hole, 0.874 inch (22.2mm) total width
    Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings.
    Fits almost all Fox rear shocks.
    Ref 214-08-007  FTW 1020988

    Fox Part Code;  803-03-259 Learn More
  14. Shock mounting hardware by X-Fusion
    Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
    Pin with 6 mm bolt hole, 21.8 mm width & 1/2" (12.7 mm) diameter
    Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks

    X-Fusion Part Code: 42-XRKBU06218-101 Learn More
  15. Shock mounting hardware by X-Fusion
    Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
    Pin with 6 mm bolt hole, 22.2 mm width & 1/2" (12.7 mm) diameter
    Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks

    X-Fusion Part Code: 42-XRKBU06222-101 Learn More
  16. Shock mounting hardware by X-Fusion
    Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
    Pin with 8 mm bolt hole, 21.8 mm width & 1/2" (12.7 mm) diameter
    Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks

    X-Fusion Part Code: 42-XRKBU08218-101 Learn More
  17. Shock mounting hardware by X-Fusion
    Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
    Pin with 8 mm bolt hole, 22.2 mm width & 1/2" (12.7 mm) diameter
    Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks

    X-Fusion Part Code: 42-XRKBU08222-101 Learn More
  18. Shock mounting hardware by X-Fusion
    Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
    Pin with 8 mm bolt hole, 30 mm width & 1/2" (12.7 mm) diameter
    Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks

    X-Fusion Part Code: 42-XRKBU08300-101 Learn More
  19. Shock mounting hardware by X-Fusion
    Includes one pair of flanged polymer bushings, aluminium pin, two collars & o-rings
    Pin with 8 mm bolt hole, 20 mm width & 1/2" (12.7 mm) diameter
    Fits 1/2" eyelets in X-Fusion, Fox, RockShox, Manitou etc. shocks

    X-Fusion Part Code: 42-XRKBU08200-101 Learn More
  20. Shock Hardware Kit - 8 x 21.85 mm, 5 piece (FOX)

    8 mm bolt hole, 0.86 inch (21.85mm) total width
    Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings.
    Fits almost all Fox rear shocks.
    Ref 214-09-066  FTW 747764

    Fox Part Code;  803-03-279

    Old Fox Part Code;  803-03-165 Learn More
  21. Shock Hardware Kit - 8 x 19 mm, 5 piece (FOX)

    8 mm bolt hole, 0.75 inch (0.19mm) total width

    Contains one pair of flanged polymer bushings, aluminim pin, two collars and o-rings.
    Fits almost all Fox rear shocks.

    Ref 214-09-004 FTW 824507
    Fox Part Code; 803-03-277 Learn More
  22. Shock Hardware Kit - 10 x 22.2 mm (FOX)

    10 mm bolt hole, 0.874 inch (22.2mm) total width
    Contains one pair of flanged polymer bushings, aluminim pin, two collars, two crush washers and o-rings.
    Fits almost all Fox rear shocks.

    Ref 214-11-001 FTW 779690
    Fox Part Code; 803-03-317

    Learn More
  23. Fits Manitou rear shocks with 1/2" ID eyelets (including McLeod, Radium, Revox & Swinger etc 2007 & later)
    21.8 mm total width 8 mm bolt hole
    Two piece top-hat design
    Manitou Part Code: 142-27125-K003 Learn More
  24. Three piece shock hardware.
    12.7mm (1/2") pin
    6mm bolt hole
    16mm total width
    Black anodised aluminium.
    Works with DU or IGUS bushings.

    SRAM Part Code:  11.4115.012.320 Learn More
  25. Three piece shock hardware.
    12.7mm (1/2") pin
    8mm bolt hole
    54mm total width
    Black anodised aluminium.
    Works with DU bushings.

    SRAM Part Code:  11.4115.012.290 Learn More

Set Descending Direction

1-25 of 35

Page:
  1. 1
  2. 2