We're excited to announce the launch of Biken Distribution.
Biken has grown from all the brands and products at Shockcraft that aren't strictly suspension, and includes a special focus on quality kids' MTB products.  Visit Biken
 

Upgrade Parts

Set Descending Direction

1-25 of 36

Page:
  1. 1
  2. 2
  1. 10 mm Shaft Clamp (Vorsprung)

    US$21.12

    In stock

    Shaft clamp tool for use in installation of Luftkappe & Secus

    Learn More
  2. ABS+ compression damper kit to upgrade Manitou 32 mm forks (Minute/Marvel/Machete/Drake/Circus/Tower).
    Includes damper and machined aluminium knob with retainer screws.
    Pro level with aluminium knobs and piston.
    Fitment: M30 x 1.0 mm cap threads, 27.85-28.9 mm piston
    Tune: ABS+ production XC stack (CV-11411-03).  Fully tunable and re-valvable to fit any rider weight or terrain.

    Shim kit and revalving instructions here.

    Manitou Part Code: 141-26532-K013

    Learn More
  3. ABS+ Circus Comp Damper Kit (Manitou)

    US$92.80

    Available on backorder

    ABS+ damper kit to upgrade Manitou Circus Comp 32 mm jump forks with steel legs
    Includes damper and moulded plastic knob with retainer screws and index balls/springs.
    Gold anodised alloy piston is 29mm OD (excluding oring) and only fits the chromed steel legs, it will not fit alloy stanchion forks.
    Jump tune features a lot of compression damping.
    Fitment: M30 x 1.0 mm cap threads, 29 mm piston
    Tune: ABS+ Jump stack (SC-03092011).  Fully tunable and re-valvable to fit any rider weight or terrain.

    Manitou Part Code: 141-26532-K006

    Learn More
  4. ABS+ Circus Expert Damper Kit (Manitou)

    US$85.05

    Available on backorder

    ABS+ damper kit for Manitou Circus Expert 32 mm jump forks with alloy legs
    Includes damper and moulded plastic knob with retainer screws and index balls/springs.
    Red alloy piston is 28mm OD (excluding oring) and fits fits the majority of Minute, Marvel, Machete and Circus Expert forks.
    Fitment: M30 x 1.0 mm cap threads, 28 mm piston
    Tune: ABS+ Jump stack (SC-03092011).  Fully tunable and re-valvable to fit any rider weight or terrain.

    Manitou Part Code: 141-26532-K007 Learn More
  5. ABS+ compression damper kit to fit Manitou J-Unit Machete 20" forks.
    Includes damper and plastic adjuster knob with retainer screws.
    Comp level with pastic knobs and damper piston.
    Shorter length than usual 32mm ABS+ dampers.
    Fitment: M30 x 1.0 mm cap threads, 27.85-28.9 mm piston
    Tune: J-unit Kids.  Fully tunable and re-valvable to fit any rider weight or terrain.

    Manitou Part Code: 141-36683-K009 Learn More
  6. ABS+ compression damper kit for Manitou R7, M30 & Markhor forks.
    Fully tunable and revalvable.
    25mm green piston and M26.5x1.00mm cap threads.

    Manitou Part Code: 141-26532-K001

    Learn More
  7. ABS+ Tuning Mini Kit (Manitou)

    US$16.19

    In stock

    Shims, balls & springs for DIY tuning of Manitou ABS+ compression dampers
    ABS+ tuning guide can be found here
    Manitou Part Code: 141-32511-K001

    Learn More
  8. Circus Pro IVA Long Upgrade Kit (Manitou)

    US$67.46

    Available on backorder

    IVA: Incremental Volume Adjust A 5 position spacer system to tune positive air chamber volume and increase progression
    Thread M31 x 0.8 mm
    Finer thread than the Mattoc/Magnum IVA upgrade kit

    Manitou Part Code: 141-35384-K006 Learn More
  9. Corset for Fox FLOAT Rear Shocks (Vorsprung)

    Regular Price: US$140.11

    Special Price US$70.06

    Vorsprung Corset air sleeve with higher volume negative
    Fits Fox FLOAT and DHX Air rear shocks
    Requires grease and air chamber lubricant (Float Fluid or RWC APL) to install

    Learn More
  10. Dorado IRT Kit (Manitou)

    US$128.22

    Last One Left

    Dorado IRT (Infinite Rate Tune) upgrade assembly Fits all Manitou Dorado forks 2009 onwards Easy installation in place of lower leg air cap Includes instructions & pressure guide Manitou Part Code: 141-32668-K005 Learn More
  11. Vorsprung Fractive upgrade tuning kit for Fox FIT4 Factory-Series fork dampers 2015-2019
    Fits only FIT4 factory series dampers with LSC adjuster dial in centre of the Firm-Medium-Open dial
    Requires significant tools and knowledge to install
    Can be installed as part of any Shockcraft complete-fork or damper-only service (book here)

    Learn More
  12. Shockcraft modified High Flow piston (rebound & mid valve) for Pro level forks with cartridge rebound
    Fits Manitou Mattoc Pro, Magnum Pro, Mastodon Pro, Minute Pro, Machete Pro etc.
    This piston greatly increases oil flow on sharp impacts and on very rough ground at speed, increasing reaction speed, removing high speed harshness and allowing more compression damping to be run
    Blue aluminium with PTFE glide-ring 16 mm OD
    Part Code: 126-27209HF

    Exchange high flow pistons also available

    Learn More
  13. Replacement IFP (internal floating piston) set for DT Equalizer 2 & 3 rear shocks
    Designed and Manufactured by Shockcraft
    These were pull shocks fitted to Scott Genius Bikes in the mid 00's to early 10's
    Originals have seals which are unservicable
    These take standard O-ring seals
    Sold as a pair, only available with Shockcraft Service Learn More
  14. Spring backed IFP (internal floating piston) set for 2002-2003 Manitou Dorado
    Designed and Manufactured by Shockcraft
    These Dorado used a foam compensator which fall apart from age.
    New IFP setup uses a coil spring and standard sized seals for future servicability

    Available as a kit or installed by Shockcraft Learn More
  15. Adapter for installing 2014+ RS Pike/Lyrik Solo Air Luftkappe for A2 chassis Pike into 2018 RockShox Pike with B1 chassis.

    Note 29+ Pike (2017/18) is built on the Lyrik/Yari B1 chassis and does not require this adapter.

    Learn More
  16. Vorsprung Luftkappe air piston with higher volume negative
    Fits 2018+ Fox Float 34 Evol Performance & Factory Series forks
    Requires roll pin tool to install as it is pinned to the air shaft.
    Can be installed as part of any Shockcraft service (book here)

    Learn More
  17. Vorsprung Luftkappe air piston and low volume sealhead for Fox 34 NA2 forks
    Fits 2016-17 Fox Float 34 NA2 Performance & Factory Series forks (130+ mm only)
    Requires shaft clamp to install and is threaded onto air shaft.
    Included low volume sealhead increases negative volume similar to 2018 Evol spec
    Can be installed as part of any Shockcraft service (book here)

    Learn More
  18. Vorsprung Luftkappe air piston with higher volume negative
    Fits 2018+ Fox Float 36 Evol Performance & Factory Series forks
    Requires roll pin tool to install
    Can be installed as part of any Shockcraft service (book here)

    Learn More
  19. Luftkappe for Fox Float 36 NA1 2015-17 (Vorsprung)

    US$122.83

    Available on backorder

    Vorsprung Luftkappe extended air piston and low volume sealhead for Fox 36 NA1 forks
    Fits 2015-17 Fox Float 36 NA forks with central needle in air chamber
    Requires 10 mm shaft clamp to install
    Included low volume sealhead extension increases negative volume further
    Can be installed as part of any Shockcraft service (book here)

    Learn More
  20. Vorsprung Luftkappe air piston with higher volume negative
    Fits 2014-2017 RockShox Pike & Lyrik forks
    Fits 2018+ Lyrik & Yari
    Fits 2018+ Rockshox Pike with an A2 Adapter.
    Not compatible with Debonair V2 or V3 shafts.
    Requires 10 mm shaft clamp to install
    Can be installed as part of any Shockcraft service (book here)

    Learn More
  21. Roll pin tool for use in installation of Luftkappe in Fox Float 34 Evol 2018+, 34 NA2 2016-17 & 36 Evol 2018+ forks

    Learn More
  22. Mattoc Pro MC2 Upgrade Kit (Manitou)

    Starting at: US$12.28

    Upgrade your Mattoc Expert to Mattoc Pro specification.
    Requires the Mattoc Pro rebound shaft assembly
    Compression damping requires either the Mattoc Pro MC2 compression assembly or convert your Expert compression damper with the Pro HBO Cup.
    27" wheel size for up to 160 mm travel

    Manitou Part Codes: 141-30996-K017 (Rebound Assembly) & 141-30996-K001 (Compression Damper Assembly) or 126-30377 (Mattoc Pro HBO Cup)

    Learn More
  23. Mattoc/Magnum IRT Upgrade Kit (Manitou)

    US$107.94

    Last One Left

    IRT: Infinite Rate Tune
    Adds a second air chamber for independent tuning of mid-end stroke.
    Coarse thread M32x1.0mm for 2014-2019 Mattoc, Magnum, Mastodon Pro and Expert level forks.
    Manitou Part Code: 141-32668-K003 Learn More
  24. IVA: Incremental Volume Adjust A 5 position spacer system to tune positive air chamber volume and increase progression Manitou Part Code: 141-32668-K001 Learn More
  25. King can multi-volume air can Choose between medium or high volume with internal seal placement Direct fit on to McLeod rear shocks Fits 190x 50 mm & 200 x 50 mm McLeod rear shocks Manitou Part Code: 142-31535-K030 Learn More

Set Descending Direction

1-25 of 36

Page:
  1. 1
  2. 2